Compression and Leak-Down Testing: Reading the Numbers Correctly
An Astra with 140,000 miles comes in with a rough idle and a small but steady loss of power. A compression test shows cylinder 2 down by 20% against the others, enough to explain the symptoms but not enough on its own to say why. A leak-down test on the same cylinder points the finger squarely at the exhaust valve, and that’s the difference between quoting a head gasket job and quoting a valve job, which is why the two tests exist together rather than as alternatives.
The tools
A compression test needs a gauge with the correct thread adapter for the engine, petrol spark plug thread or diesel glow plug/injector adapter, the battery in good condition since you’re cranking the engine repeatedly, and ideally the engine warmed up first, since a cold engine reads lower than its true compression. A leak-down tester is a different instrument: two gauges either side of a calibrated orifice, fed by shop air, that measures how much pressure is lost from a cylinder held at top dead centre on the compression stroke, expressed as a percentage.
The procedure
- Warm the engine, then remove all spark plugs or injectors so the starter isn’t fighting compression on every cylinder.
- Disable ignition (petrol) or fuel delivery (diesel) so the engine doesn’t attempt to fire during cranking.
- Crank each cylinder through 4-5 compression strokes with the throttle held open, and record the reading.
- Compare cylinders against each other; a healthy engine should show readings within roughly 10% of the highest cylinder, not against a generic figure pulled from a different engine.
- For any cylinder reading low, follow up with a leak-down test on that cylinder at TDC compression stroke, and listen at the intake, exhaust and oil filler while the air is applied.
What the numbers mean
A low compression reading tells you something is wrong; a leak-down test tells you what. Air escaping from the intake points to an intake valve not sealing. Air from the exhaust points to an exhaust valve, often burnt on a high-mileage engine or one that’s run lean. Air from the oil filler cap or dipstick tube points to worn piston rings or a scored bore, since that air is passing the rings into the crankcase. Air bubbling into the coolant expansion tank, visible with the cap off, is one of the more reliable ways to confirm a head gasket failure between a cylinder and the water jacket, alongside a chemical block test.
Ring problem versus valve problem, at a glance
- Low compression, leak-down loss from the oil filler: rings or bore wear.
- Low compression, leak-down loss from the exhaust pipe: exhaust valve not sealing.
- Low compression, leak-down loss from the intake: intake valve or possibly a stuck valve.
- Low compression on two adjacent cylinders, leak-down loss shared between them: usually a blown head gasket between those cylinders.
Where this crosses over with electronics
It’s worth ruling out an electronic cause before assuming a mechanical one. A weak injector, an intake leak, or a timing chain that’s stretched enough to affect valve timing without triggering a fault code can all mimic a low-compression symptom without any actual mechanical damage present. On a timing-chain-sensitive engine like the EA888 or N47, check timing marks and chain stretch before condemning a cylinder purely on a compression number, since the fix in that case is a chain, not a rebuild.
Where the real cause turns out to be a sensor or a corrupted file rather than a mechanical fault, our fault codes and diagnostics section and the guide to reading ECU label numbers are useful next steps before you commit to stripping anything down.
More ECU guides
J2534 Pass-Thru Devices Explained: What They Do and When You Need One
A Stellantis van needs a body control module replaced and paired to the vehicle, and the aftermarket scan tool on the shelf can read every fault…
Borescope Engine Inspection: Checking Turbos and Cylinders Without Stripping
A customer wants a second opinion before spending a large sum on a turbo replacement quoted elsewhere. Rather than pulling the turbo off the car on…
Multimeter and Oscilloscope Basics Every Workshop Should Know for Diagnostics
A misfire on cylinder 3 that only shows up at idle, no stored code, and the customer swears it "does it every morning." A multimeter confirms…